9/1/2023 0 Comments Motion raceworks coil brackets![]() If you made it this far you likely understand the importance of quality and highly accurate sensors that do not fail. If this sensor fails and reads low (pressure sensors typically read to zero or very low when they go bad), the solenoids will subsequently keep adding pressure to try to achieve the boost level creating extreme over boost situations. However, do not cheap out with an inexpensive or unreliable sensor in this location. A standard 100 psi sensor is perfect for this application. This double method gives a little leeway and cushion. While most times you add 5 psi of co2 to make 5 more pounds of boost, some combos may require 2 to 1 meaning 10 psi of co2. So 30 psi of boost as a target, get a 100 psi sensor. This one is very simple, however many psi of boost you are trying to achieve the sensor is typically needing to be no more than double that. This sensor will tell the solenoids externally mounted whether they need to add more or remove pressure to hit their target. This sensor is essential in effectively targeting and managing boost and mounts directly or taps in directly to the top of the wastegate dome where manifold or compressed (co2 or onboard air) is being applied. It opens to remove exhaust pressure pre turbo, and closes to add more in order to achieve a target amount of boost. Your wastegate acts as a regulator for boost. For example between intake runners rather than at the back of the intake manifold where air does not flow past. These sensors need to go post intercooler and should be in a place that is representative of the air going in the intake runner. These can be found HERE in a variety of sizes and plug styles. As a little bit of a plug, we sell a fast response sensor that is 15x faster and 3x more accurate. This is concerning and can cause many issues. This means that your engine may have intake air temperatures much higher than the sensor is reading, and your efi system is tuning to that wrong info. Factory Style IAT sensors as commonly used by big name EFI companies and sold by many retailers are SLOW response. This one is often overlooked but needs to be there, be a good fast response sensor, and needs to be in the correct location. Note these are different than a factory style Narrowband sensor. This is essential as a reference for your ECU to operate off of for aftermarket ECU and as a reference for even factory style ECU that your tuner will tune off of. Again do not put too large of a sensor compared to what you need as it reduces resolution and the ecu ability to react to small changes. For this reason you will need a 3 bar minimum sensor which reads to 29 psi, 4 bar reads to 43.5 psi, 5 bar reads to 58 psi. This is of course not sufficient for boost. Factory cars that are not built with forced induction come equipped with a 1 bar map sensor which essentially measures vacuum up to a ceiling or ambient atmospheric pressure (no boost). This lets your ECU know where in the table fueling needs to be. ![]() This sensor monitors the vacuum and also positive (boost) pressure in your intake manifold. Keep in mind you do not want to go way too large on the sensor as the greater the max pressure of the sensor the lower the resolution is. So if you are starting at 85 psi and adding 30 psi, you need a 115 so a 150psi sensor would be best. However, with some injectors and tuning styles base pressure may start much higher in order to maximize a fuel injector, etc. ![]() You want to leave some wiggle room for growth an extreme instances. If I am running 30 psi of boost I need atleast a 73.5 lb worth of fuel pressure sensor. For instance 43.5 lb is a very common base pressure. This can easily be figured out by adding your base fuel pressure to the amount of boost you want to run. Typically this sensor needs to be 100 or 150psi. This means that for every pound of boost, the fuel pressure regulator adds a pound of fuel pressure to overcome the boost in the intake in delivering enough fuel. Please note this list doesn't mention standard engine sensors such as coolant, oil pressure, tps, iac, etc as they are needed on any EFI engine.īoosted applications utilize a boost reference style fuel system. So we went ahead and put together the basics and then some "would be nice" below. Lets face it, you don't do this for a living and the internet can be a very cloudy place for information. With the rapid growth of forced induction and technology that goes along with it, the sensors and what is actually needed can be quite daunting. So this is your first EFI setup? Or first turbocharged combination.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |